Softub Pump: 1.5HP (Spl), 1 Speed W/Thermal Wrap (Replaces XP2e) No Base Motor

Softub Pump: 1.5HP (SPL) 12 Amps, 1 Speed with Thermal Wrap (replaces XP2e pump)With No Base MotorThis system is designed to replace your existing coil wrapped motor with our patented "Thermal Wrap" Heat Jacket - for less money! This System/Listing Includes:Motor & Pump with Pre-installed Thermal WrapDescriptions:Motor: Manufacture: Century / A.O. Smith / Single Speed Motor - No Base Horse Power: 1 Service Factor 1.0 (1.5hp SPL) Volts: 115 Amps: 12.4 RPM: 3450 Frame: 48Y HZ: 60 Stainless Shaft Thermally Protected Pump: (pre-installed on motor) Manufacture: Aqua-Flo P/N: 9phone - FMHP Series 1 HP (1.5HP SPL) 1 1/2" Center Suction x Side Discharge - pump threads fit 1.5" pump disconnects/unions.2) Pump Thread Adaptors - 1.5" Female x 2" Male (These adaptors are included and necessary for this pump 1.5" threads to fit Softubs supplied with an XP2 pump with 2" pump threads, unions/disconnects) see adaptors installed on pump threads in second picture above.1) Thermal Wrap Heat Jacket: Pre-installed on motor (top port on Thermal Wrap is plugged and not used for Softub applications) 32") 3/8" ID Tubing (for making tubing connections between the 2 ports on Thermal Wrap to your existing coil/hose ports in your plumbing) 4) Tubing Clamps Warranty: 2 years manufactures warranty applies to pump and motor. Life time warrant applies to Heat Recovery Jacket. Note: Some older model Softubs were supplied with a front discharge pump - to view this older style pump search classifieds board item number: phone6 Note: For 220/230 Volt Softub Pump Replacement Typically used in "European" markets: Search classifieds board item numbers: phone5 & phone6 (for XP2e)1 HP, *** 230 Volts ***, 50HZ, Single Speed with Pre-Installed "Thermal Wrap" Heater Jacket ____________________________________________________ More about the Thermal Wrap - Heat Transfer System: Tub water circulates through a serpentine path in the Thermal Wrap, collecting the heat generated by the pump/motor and recycles that heat to the tub water - were it belongs!

This patented heating system for hot tubs/spas and Whirlpool Baths, captures and recycles the waste heat "energy" produced by the pump/motor and delivers that heat to the hot tub or bath water. The Thermal Wrap system will heat and maintain water temperature.The system allows the motor to run cooler; increasing the motors longevity and efficiency.There are no moving parts and nothing to wear out. Made in the USA! Efficient:- Patented design, over 1,000,000 in use- Special thermal conductive inner heat transfer liner- Models available for most 48 frame thru bolt spa/hot tub and jetted bathtub pumps Economical:- Maintenance free - no moving parts to wear out- Helps keep motor cooler - increases motor longevity and efficiency- Cost less than electric heaters- No additional electrical circuits required for installation Safe:- Manufactured of non-conductive materials- Non electrical- Self draining design (required for whirlpool bath application) Note: If the pump/connections pictured above do not exactly match the pump have? Give me a call to discuss your application, we either have the pump you need or have other available options that will work for your application.

Replacement pump and motor with the Thermal Wrap serves as the only heat source for many spas including: Quantum, Dreammaker, FreeFlo, PDC spas, Softub and others. Can be used and retrofitted to work with most spas requiring 1 hp single speed, 3450 rpm, 115volts pump motor. Even if you have an electric heater on your spa, the Thermal Wrap System will compliment your electric heater by capturing the waste heat generated by your pump motor and delivering that heat to the tub water, saving you money with heating costs.The Thermal Wrap will help maintain water temperature during normal filtering and heating cycles and while using your spa in high speed jet action.Visit our classifieds board Store for more pumps, motors and controls for hot tubs.